TEAC X-2000 2000M 2000R complete electrolytic capacitor set recap repair

Information on product safety

- Please keep out of the reach of children!

- Contains small parts, risk of suffocation!

- Electrolytic capacitors may contain toxic electrolyte!
Risk of poisoning!

- Polarity must be observed!

- Work with the device unplugged and de-energized

- Capacitors may still store life-threatening voltages even after a long period of non-use!

Information on product safety

- Please keep out of the reach of children!

- Contains small parts, risk of suffocation!

- Electrolytic capacitors may contain toxic electrolyte!
Risk of poisoning!

- Polarity must be observed!

- Work with the device unplugged and de-energized

Information on product safety

- Please keep out of the reach of children!

- Contains small parts, risk of suffocation!

- Electrolytic capacitors may contain toxic electrolyte!
Risk of poisoning!

- Polarity must be observed!

- Work with the device unplugged and de-energized

- Capacitors may still store life-threatening voltages even after a long period of non-use!

Information on product safety

- Please keep out of the reach of children!

- Contains small parts, risk of suffocation!

- Electrolytic capacitors may contain toxic electrolyte!
Risk of poisoning!

- Polarity must be observed!

- Work with the device unplugged and de-energized

- Capacitors may still store life-threatening voltages even after a long period of non-use!





Information on product safety

- Keep out of reach of children!

- Contains small parts, risk of suffocation!

- Electrolytic capacitors may contain toxic
electrolyte! Risk of poisoning!

- Polarity must be observed!

- Work with the device disconnected from the power supply and de-energized

- Capacitors may still store life-threatening voltages
even after a long period of non-use!

Information on product safety

- Please keep out of the reach of children!

- Contains small parts, risk of suffocation!

- Electrolytic capacitors may contain toxic electrolyte!
Risk of poisoning!

- Polarity must be observed!

- Work with the device unplugged and de-energized

- Capacitors may still store potentially fatal voltages
even after a long period of non-use!

Information on product safety

- Keep out of reach of children!

- Contains small parts, risk of suffocation!

- Electrolytic capacitors may contain
toxic electrolyte! Risk of poisoning!

- Polarity must be observed!

- Work with the device unplugged and de-energized-
Capacitors may still store potentially fatal voltages
even after a long period of non-use.

Installation and assembly instructions

This type-specific capacitor set is intended to replace
the electrolytic capacitors present in the respective device; either because
because the existing capacitors are defective or because the ones we offer
better than the original ones (upgrade).

1. First of all, it is advisable to take lots of photos. Of
of the wiring, circuit board, and capacitors. It is helpful if you can
check how the capacitor you are currently holding between your fingers was installed
the wiring, circuit board, and capacitors. It is helpful if you can
between your fingers so that you can install the new one the right way round

(in some cases, the markings on the circuit board cannot be trusted, if present).
note that in the vast majority of cases the new electrolytic capacitors
were supplied with a higher voltage rating 1.

3. Proceed in order: desolder a defective electrolytic capacitor
desolder a defective electrolytic capacitor and solder in a new one.

1 The maximum permissible voltage (V) rating may match that of the
of the old capacitor

match the old capacitor, but it may certainly be higher and must never
never be lower.

An example:

Your device contains four different types of
47µF capacitors

installed:

47µF/10V, 47µF/25V,

47µF/35V and

47µF/50V.

As replacement types, we would supply the following
receive:

2x 47µF/35V as a replacement for 10V and 25V

2x 47µF/63V as a replacement for 35V and 50V

Although the original includes a 35V capacitor, a
so that

the voltage rating is higher, a 63V capacitor
supplied.

2 We recommend desoldering with the help of
desoldering braid and a manual desoldering pump. The best option would be
an electronic desoldering station with a heated suction gun, but purchasing one
is generally not worthwhile for smaller projects.

Installation and assembly instructions

This type-specific capacitor set is intended to replace the
electrolytic capacitors in the respective device; either because the existing
capacitors are defective or because the ones we offer are of better quality
than the original ones (upgrade).

1. First of all, it is advisable to take lots of photos. Of
the wiring, circuit board, and capacitors.

Electrolytic capacitors are generally polarized; they have a
positive and negative lead or side. It is helpful if you can look up which way
capacitor you are holding between your fingers was installed so that the new
it can be installed the right way round (in some cases, you cannot trust the
circuit board markings, if any).

2. Then, get an idea of the situation. Remember that in the
vast majority of cases, the new capacitors were supplied with a higher voltage rating
resistor (see note about the permitted voltage below).

3. Proceed in order: desolder an old capacitor, solder in a
new one (see note about desoldering tools below)

Permissible Voltage: The value of the maximum permissible
voltage (V) may match that of the old capacitor, but may be higher and may
NEVER be smaller, unless the device's service manual shows a lower voltage
at that point.

An example:

Your device has four different types of 47µF capacitors
installed:

47µF/10V, 47µF/25V,

47µF/35V and

47µF/50V.

We would supply you with the following replacement types:

2x 47µF/35V as a replacement for 10V and 25V

2x 47µF/63V as a replacement for 35V and 50V

Although the original comes with a 35V capacitor and we
could supply a 35V, a 63V capacitor is supplied to increase the voltage
resistance.

Desoldering tools: In individual cases, we recommend
desoldering using desoldering braid and a manual desoldering suction pump.
best option would be an electronic desoldering station with a heated suction
gun, but this is usually not worth buying for smaller projects.

Assembly and installation instructions

This type-specific capacitor kit is intended to
replace the electrolytic capacitors in the device concerned; either because
that the existing capacitors are defective, either because the ones we
we offer are of higher quality than the originals (upgrade).

1. First, it is advisable to take plenty of
photos. The wiring, circuit board, and capacitors.

Electrolytic capacitors are generally
polarized, they have a positive and negative lead or side. It is a good idea to
be able to check which way the capacitor you are holding between your fingers
was installed so that the new one can be installed in the correct orientation (so that
in some cases, you cannot rely on the markings on the circuit
printed on it, if any).

2. Next, assess the situation. Remember
noting that in the vast majority of cases, the new capacitors have been
supplied with a higher voltage rating (see the note on voltage
permissible voltage below).

3. Proceed in order: desolder an old capacitor,
solder a new one (see the note on desoldering tools below)

Permissible voltage: The maximum permissible voltage
permissible (V) may match that of the old capacitor, but may
be higher and can NEVER be lower, unless
the device's service manual indicates a lower voltage at this point.

An example:

Your device is equipped with four different types of
47µF capacitors installed:

47µF/10 V, 47µF/25 V,

47µF/35 V and

47µF/50 V.

We offer you the following replacement types:

2x 47µF/35V as a replacement for 10V and 25V

2x 47µF/63V as a replacement for 35V and 50V

Although the original comes with a 35V capacitor
and so that we can supply a 35V, a 63V capacitor is supplied to
increase the voltage rating.

Desoldering tools: in some cases, we recommend
to desolder using desoldering braid and a suction pump
manual desoldering iron. The best option would be a desoldering station
electronics with a heated suction gun, but it isn't worth
generally isn't worth buying it for smaller projects.

Installation and assembly instructions

This type-specific capacitor set is intended
to replace the electrolytic capacitors in the respective device; both because
the existing capacitors are defective, and because those we offer are of
better quality than the original ones (upgrade).

1. First of all, it is advisable to take many photos. Of the
wiring, circuit board, and capacitors.

Electrolytic capacitors are generally polarized,
have one positive and one negative lead or side. It is helpful if you can
check how the capacitor you are holding was installed
finger so that the new one can be installed correctly (in
in some cases you cannot rely on the circuit board markings, if there are
they are).

2. Then, get an overview of the situation. Remember that in
in the vast majority of cases, the new capacitors have been supplied with
a higher voltage rating (see the note on permissible voltage
below). 3. Proceed in order: desolder an old capacitor,
solder a new one (see the note on desoldering tools
below)

Permissible voltage: the maximum voltage rating
permissible voltage (V) may match that of the old capacitor, but it may
be higher and can NEVER be lower, unless the device's service manual
device's service manual does not specify a lower voltage at that point.

An example: The device has four different types of
47µF capacitors installed:

47µF/10V, 47µF/25V,

47µF/35V and

47µF/50V.

 We will provide you with the
following replacement types:

2x 47µF/35V as a replacement for 10V and 25V

2x 47µF/63V as a replacement for 35V and 50V

Although the original is equipped with a 35V capacitor and
we could supply one rated at 35V, a 63V capacitor is supplied
increase the voltage rating.

Desoldering tools: in individual cases, we recommend
to desolder using desoldering braid and a suction pump
manual desoldering iron. The best option would be a desoldering station
electronics with a heated suction gun, but it usually isn't worth the
worth buying it for smaller projects.

Installation and assembly instructions

This type-specific capacitor set is intended to
to replace the electrolytic capacitors in the respective device; or
because the existing capacitors are faulty, either because the capacitors that
that the ones we offer are of better quality than the originals (upgrade).

1. First of all, it is advisable to take many photographs. Of
the wiring, the printed circuit board, and the capacitors.

Electrolytic capacitors are usually polarized; they
have a positive and negative lead or side. It is a good idea to check
which way the capacitor you are holding between your fingers was installed,
so that you can install the new one correctly (in some cases
you cannot rely on the markings on the printed circuit boards, if any).

2. Then assess the situation. Do not forget
that in the vast majority of cases the new capacitors were
supplied with a higher voltage rating (see the note on permitted
voltage below).

3. Proceed in the correct order: desolder an old
capacitor, solder in a new one (see the note about tools for
desolder below)

Permitted voltage: The value of the maximum permitted
voltage (V) may match that of the old capacitor, but may be higher
and must NEVER be lower, unless the device's service manual
that point indicates a lower voltage.

An example:

Your device has four different types
47µF capacitors installed:

47µF/10V, 47µF/25V,

47µF/35V and

47µF/50V.

We supply you with the following replacement types:

2x 47µF/35V as a replacement for 10V and 25V

2x 47µF/63V as a replacement for 35V and 50V

Although the original comes with a 35V capacitor
and when we can supply you with a 35V one again, a 63V capacitor is included to
to increase the voltage rating.

Desoldering tool: In individual cases
we recommend desoldering using desoldering braid and a manual
desoldering pump. The best option would be an electronic desoldering station with a
There may be a heated desoldering gun, but this is usually too expensive to buy for
smaller projects.

Installation and assembly instructions

This type-specific capacitor set is
intended for replacing the electrolytic capacitors in a given device;
either because the existing capacitors are faulty or because the ones offered
we supply are of better quality than the originals (upgrade).

1. First of all, it is advisable to take many photos.
Wiring, printed circuit board, capacitors.

Electrolytic capacitors are generally polarized,
have a positive and negative lead or side. It is a good idea to check which way
the capacitor that you are holding between your fingers was installed so that the new one could
be installed correctly (in some cases, you cannot rely on
printed circuit board, if any).

2. Then, assess the situation. Remember that in
in the vast majority of cases, the new capacitors were supplied with
higher voltage rating (see note on permitted voltage
below).

3. Proceed in order: desolder the old capacitor, solder in
a new one (see note on desoldering tools below)

Permitted voltage: The maximum permitted voltage rating
voltage (V) may match the voltage of the old capacitor, but may be higher
and can NEVER be lower, unless the device's service manual
indicates a lower voltage at this point.

Example:

Four different types of capacitors are installed in the device
47µF:

47µF/10V, 47µF/25V,

47µF/35V and

47µF/50V.

We will provide you with the following replacement types:

2x 47µF/35V as a replacement for 10V and 25V

2x 47µF/63V as a replacement for 35V and 50V

Although the original is fitted with a 35V capacitor, and we
we can supply 35V, a 63V capacitor is supplied to increase the
voltage rating.

Desoldering tools: In individual cases
we recommend desoldering with desoldering braid and a manual suction pump for
desoldering. The best option would be an electronic desoldering station
with a heated suction gun, but it is usually not worth buying one for smaller
projects.

Installation and assembly instructions

This specific set of capacitors is intended
to replace the electrolytic capacitors in the respective device; whether
because the existing capacitors are faulty or because the ones we offer
are of better quality than the originals (upgrade).

1. First of all, it is advisable to take many
photographs. Of the wiring, the circuit board, and the capacitors.

Electrolytic capacitors are mostly
polarized; they have a positive and negative lead or side. It is helpful if you can
check how the capacitor you are holding between your fingers was
installed so that the new one can be installed correctly (in some
cases you cannot rely on the circuit board markings, if any).

2. Then, assess the situation. Remember that in
in the vast majority of cases, the new capacitors were supplied with a
higher voltage rating (see note on permitted voltage below).

3. Proceed in order: desolder an old capacitor,
solder in a new one (see note on desoldering tools below)

Permitted voltage: The maximum permitted voltage rating (V)
may match that of the old capacitor, but may be higher and NEVER
lower, unless the device's service manual indicates a voltage
lower at this point.

An example:

Your device has four different types of
47µF capacitors installed:

47µF/10V, 47µF/25V,

47µF/35V and

47µF/50V.

We will provide the following replacement types:

2x 47µF/35V as a replacement for 10V and 25V

2x 47µF/63V as a replacement for 35V and 50V

Although the original comes with a 35 V capacitor and
we can supply a 35 V one, a 63 V capacitor is supplied to increase the
voltage rating.

Desoldering tools: In individual cases,
we recommend desoldering using desoldering braid and a suction pump
manual desoldering suction tool. The best option would be a desoldering station
electronics with a heated suction gun, but it is generally not worth it
buy for smaller projects.

Installation and assembly instructions

This type-specific capacitor kit is
designed to replace the device's electrolytic capacitors
either because the existing capacitors are defective or
because the ones we offer are of better quality than the originals
(update).

1. First of all, it is advisable to take plenty of
photographs. Of the wiring, the circuit board, and the capacitors.

Electrolytic capacitors are mostly
polarized, they have a positive side and a negative side. It is good that you can
check which direction the capacitor you are holding was installed in
so that you can install the new one in the correct orientation (in some cases you cannot
you can rely on the circuit board markings, if any).

2. Next, get an idea of the situation. Remember
since in the vast majority of cases the new capacitors were supplied with
a higher voltage rating (see the note on the permitted voltage below)
continuation).

3. Proceed in order: desolder one old capacitor, solder
a new one (see the note about desoldering tools below)
continuation)

Voltage rating: the maximum permitted voltage value (V)
may match that of the old capacitor, but it may be higher and NEVER
lower, unless the device's service manual specifies a lower voltage
lower at that point.

An example:

Your device has four different types of
47 µF capacitors:

47 µF/10 V, 47 µF/25 V,

47 µF/35 V and

47 µF/50 V.

We will supply you with the following replacement types:

2x 47µF/35V as a replacement for 10V and 25V

2x 47µF/63V as a replacement for 35V and 50V

Although the original comes with a 35V capacitor and
we could supply a 35V one, a 63V capacitor is supplied to
increase the voltage rating.

Desoldering tools: In individual cases,
we recommend desoldering using desoldering braid and a suction pump
manual desoldering tool. The best option would be a desoldering station
electronics with a heated suction gun, but it is generally not worth it
worth buying it for smaller projects.

TEAC